Tag Archives: wheel bearing

Replacing struts at the shop costs four hundred to eight hundred dollars a corner, and the bill is enough to make any home mechanic wonder whether the job is doable in the driveway. The answer depends on whether you choose a complete strut assembly or a cartridge, and on whether you are comfortable using a spring compressor. With the right tools and a complete assembly, the job takes a couple of hours and saves half the bill.

Trucks and SUVs wear struts and shocks faster than passenger cars, because they carry heavier loads, see rougher roads and often tow trailers. The factory strut on a Ford F-150 or Chevrolet Silverado is tuned for an empty truck, which means it is under-damped the moment you load the bed with tools or hook up a trailer. Replacing them with the same OEM spec brings back the empty-ride feel but does nothing for the loaded duty cycle. A heavy-duty upgrade is often the better choice.

A clunk or click that appears only when turning the steering wheel at low speed is one of the most common front-end complaints, and the cause is almost never the power steering pump or the rack. The noise comes from the top strut mount bearing, which allows the strut to turn with the steering wheel. When that bearing wears out, every steering input produces a click or clunk that the driver hears in the cabin. The fix is usually inexpensive, but it is often misdiagnosed.

The strut mount is the small rubber and bearing assembly that sits between the strut and the body. It is the least expensive part in the front suspension, but when it wears, it produces a surprising number of symptoms that get blamed on everything from the power steering pump to the ball joints. Learning the six key signs helps pinpoint the problem quickly and avoids replacing parts that are not the cause.

A pickup that groans and creaks when you throw bags of mulch into the bed, or when the body twists over a driveway entrance, is usually telling you about the mounting points, not the metal parts themselves. The bed sits on the frame through body mounts, and the rear axle hangs from the frame on leaf springs, and both of those interfaces have rubber or sliding surfaces that dry out and squeal under load. Trucks of any age can do it, from a clean low-mileage work truck to a rig that has hauled for years, because the noise is about lubrication and rubber condition, not about how new the truck is.

A thump that follows the rear of the car over every bump in the road, and never seems to come from the front, is one of those noises that sounds expensive until you realize how few parts live back there. On a crossover or an SUV the rear suspension is a handful of arms, a sway bar, and two shocks, so the thump is almost always a bushing that has gone soft or a damper that has lost its hydraulic hold. The diagnosis is short, the parts are modest, and the biggest mistake is buying shocks before checking the bushings.

The car that starts creaking every time the temperature drops below freezing, and goes quiet by the time the engine warms the garage, is not falling apart; it is telling you that rubber gets stiff in the cold. Suspension bushings are engineered to flex, but their durometer changes with temperature, and a bushing that is already dry or slightly worn turns a normal flex into an audible creak at twenty degrees. The fix is usually simple, and knowing the difference between a stiff bushing and a genuinely dry joint keeps you from replacing parts that were never broken.

Run your hand across the rear tire tread of a front-wheel-drive sedan and one side of every tread block feels sharp while the other feels smooth, and you are feeling a feather edge, the signature of rear toe misalignment. The rear wheels of a FWD car do not drive the car, but they still steer it in the sense that their toe angle scrubs the tires with every mile. The wear is slow, the sound is subtle, and by the time the feathering is obvious the rear tires are usually halfway gone, which is exactly why the complaint reaches the shop as a noise rather than a wear report.

An empty truck rides smooth, but drop a load of lumber, a trailer tongue or a packed family of five in the back and the whole front end starts to buzz. That load-sensitive shake is one of the most misunderstood complaints in the shop, because the last balance job passed inspection the day before. Adding weight compresses the springs, changes ride height, and shifts every angle in the front suspension, which turns a marginal balance into a visible shake and a tired spring into a tire that walks on the pavement.